There is an extruded aluminum option that seems to work quite well. This option also takes a little bit of work but it is better than having your table move about or cause you to spill your food. Then buy a wall mount to secure both to the new wall. It is a little more work but it will make sure your table stays still.įinally, you can always reinforce your wall with 1/2 or greater plywood. Then just cut to size, drill a few holes in the pedestal and attach everything. You would need some L brackets, metal screws, and a piece of 2 by 2 wood. However, the support beam has to be placed in the right spot so it does not interfere with getting in and out of the seating area. Just in case, you can always go to screws that are a bit longer than the old ones to make sure you have a secure fit.Īnother option would be to add a support beam to hold the table still. If the component that has the screws going through it is secure, chances are you can use the same holes as you did for the old mount.
#RV DINETTE REPLACEMENT IDEAS INSTALL#
It doesn’t take much to get a new pedestal mount and install it. Because RV manufacturers use the cheapest options possible, this is a common situation. Where the pedestal mount loses its strength is the leg inside the mount. If so, you may have to order a new pedestal from the manufacturer to make it more sturdy. You cannot go to longer screws here as their points may come through the tabletop.Ī third option you have in this project is to check to see if the strength of the pedestal has weakened. If the screws are loose, then simply tighten them up. Even without shims, longer screws are the fastest and easiest method you can use to secure your table and make it sturdier.Ī second method is to check the pedestal mount that attaches to the underneath side of your table. Then once you got the balance just right, you need to go to longer screws to make sure they are biting the wood very well and are deep enough to hold the table still. If they are loose and the table is wobbly or uneven, then you will need to use some shims to balance the table out. The first step you can take in this issue is to check the current screws in your pedestal table or wall mount device. You may end up having to be creative in your use of different materials to keep the chairs from damaging themselves and other pieces of furniture or cabinets inside your RV. Finding the right mounts to secure the chairs is another issue and sometimes a little more difficult to find than standard table mounts and hardware.
Most RV owners do not secure their free-standing dinette chairs and as a result, they suffer some damage in an emergency or rush stop. The problem will come in when you start to move. There are enough tools, hardware, and location options you can use to make sure the table does not go anywhere. Securing the table is not that difficult. The bolts just have to be rated stronger than the table for them to hold the table securely. If you are using a pedestal-style table mount, the best option may be bolts as you can use nuts to secure the bolts. If your RV has wood studding, then a few tough and strong screws will hold your dinette in place no matter where you drive. When it comes to using hardware, the best item to use is screws. The trick is to have thick enough plywood to handle that job. Or, you can always reinforce your walls with plywood and attach the wall mounts to it. The wall mount option is very secure when you can find the right studding to attach it to. These pedestals attach to your flooring which gives you a lot more security than a wall mount option will.īut you will have to make the design choice that will fit your RV’s design as well as what you want to have in that spot. The most common way to secure your dinette table is by using a pedestal mount option. Sometimes you have to find ways to secure the table to the wood used to hold the window in place or the flooring beam that holds the lower wall in its spot. Many do not come with the studding you need to use a wall mount device properly. The drawback to this system is how the walls of an RV are made. Only the chairs will be the problem if they are not already secured or can be secured.
When it does, you really don't have much to worry about. There are many options you can use for this project, that is if your RV does not come with a pre-installed wall mount table or dinette.
0 kommentar(er)
